CORED WIRES FOR DIES AND FORGE EQUIPMENT
F SERIES FOR FORGING DIE AND COMPONENT RECLAMAITION
|
CORED WIRES FOR DIES AND FORGE EQUIPMENT |
|
|
|
||
| COR® FORGE |
F SERIES FOR FORGING DIE AND COMPONENT RECLAMAITION |
|
|
|
||
         |
ALLOY | DESCRIPTION | CLASSIFICATION | PHYSICALS |
| F15 FC | A very tough alloy for use in repair of columns and cylinders and other areas subject to cracking. | Fe-Ni-Cr-Mo 6% alloy |
15-20 Rc as welded 115,000 psi tensile |
|
| F25 FC | This alloy is used to buildup worn areas subject to high impact and compressive loads such as rams, sow blocks and shanks. | Fe-Ni-Cr-Mo 8% alloy |
25-30 Rc as welded 132,000 psi tensile |
|
| F35 FC | For reclamation of hammer die impressions. This alloy is similar in wear properties to die block with a number 2 temper. | Fe-Ni-Cr-Mo 10% alloy |
32-37 Rc as welded 165,000 psi tensile | |
| F40 FC | For hammer die impressions when more abrasion resistance is needed than F35 FC provides. | Fe-Ni-Cr-Mo 12% alloy |
38-43 Rc as welded 182,000 psi tensile | |
| F45 FC | For shallow hammer and press die applications | Fe-Ni-Cr-Mo 14% alloy |
42-47 Rc as welded 186,000 psi tensile | |
| F54 FC | Provides machinable deposit for press die applications | 5% Cr Hot Work | 38-42 Rc as welded | |
| F58 FC | A 5% Cr Hot Work alloy for press dies. | AISI H-12 | 51-56 Rc as welded | |
| F580 FC | A higher alloy version of F58 that withstands higher service temperatures without softening | AISI H-12 type with higher W and Mo | 51-56 Rc as welded | |
| F63 FC | For shallow hammer dies with high duty cycles and press dies subjected to high heat and stresses when a machinable deposit is required. | 9% Cr Hot Work | 42-46 Rc as welded | |
| F64 FC | For use on press dies subjected to high heat and stresses. | 11% Cr Hot Work | 48-53 Rc as welded | |
| F65 FC | For shallow hammer dies and high cycles and press dies subjected to high heat and stresses. | 9.5% Cr Hot Work | 49-52 Rc as welded | |
| 6 FC | Cobalt #6alloy that maintains hardness at high temperatures | AWS ECoCr-A | 42-46 Rc as welded | |
| 21 FC | Cobalt #21 alloy that maintains hardness and impact properties at high temperatures. | Co-Cr-Mo | 28-33 Rc as welded | |
| 2101 FC | Offers superior resistance to heat checking, spalling, chipping and erosion over our 21 alloy. | Co-Cr-Mo-Cb | 33-38 Rc as welded 45+ Rc work hardened | |
| F110 FC | Used for overlaying of forging dies and components subject to high temperatures and impacts. | AWS ENiCrMo-5 | 100,000 psi tensile min. 20 Rc as welded | |
| F111 FC | An excellent underlayment for harder nickel base alloys on high temperature forging dies. | modification of AWS ENiCrMo-5 | 20 Rc as welded 40 Rc work hardened |
|
| F112 FC | For forging surfaces exposed to high temperatures and long contact times. | modification of AWS ENiCrMo-3 | 110,000 psi tensile 30% Elongation min |
|
| F114 FC | For overlay of rotary forging dies subjected to high temperatures and stresses. | modified UDIMET®520 |
25-30 Rc as welded | |
| F115 FC | For overlay of rotary forging dies subjected to high temperatures and stresses | modified UDIMET®520 |
30-35 Rc as welded | |
| F116 FC | For overlay of rotary forging dies subjected to high temperatures and stresses | modified UDIMET®520 |
35-40 Rc as welded |
"UDIMET is a trademark of Special Metals
Corporation"
Obtain a complete one-page data sheet and temper chart
from COR-MET® for full information prior to use.